Substation Automation Solutions for Garments Sector

We offer Substation Automation Solutions for Garments Industries for Industries for boosting the efficiency of operations and avoiding unnecessary breakdowns.  We also provide training in our new installation for operation and maintenance staff of client to better understanding technology, thus increasing the plant efficiency.

Our Substation Automation Solutions for Garments industries are as follows:

Engineering Solutions:

•  Auto Transfer Scheme for Incomer and DG switchover 

A bus transfer system is designed to provide process continuity to the loads attached to a motor bus while transferring the bus from one source to another. A successful bus transfer under contingent conditions provides immense value and benefits to continuous process operations that cannot afford an interruption of power supply to plant auxiliaries.

We are experienced in designing and implementing such schemes for substations.  This can be done as a retrofit in existing panels or supplied as a new panel as per station condition and requirement.

• Load Shedding scheme

During overloads in the mains, the load shedding applied to interruptible loads is often the only solution to keep the industries in operation. Normally, in such cases, non-critical loads that are earlier identified are tripped automatically to avoid interruption of critical loads and induced penalties when power is being drawn from the grid.

We offer a range of products and solutions from Siemens/Schneider for these critical operations based on Current, Power or frequency for load shedding.

• Power System Studies and Relay Coordination’s

Relay coordination study and analysis is performed to make sure that safety operation of the system are functioning correctly and to avoid the nuisance tripping, as protection is a major concern in any industry and they rely on protective devices for the same.

The aim of a coordination study is to determine the characteristics, ratings, and settings of overcurrent protective devices which will ensure that minimum unfaulty load is interrupted when protective devices isolate a fault or overload anywhere in the system.

• Protection System Upgradation/ Retrofits with Modern Numerical Relays

Older relay usually outdated, are supposed to be replaced in industries to avoid mal tripping and ease operations in a plant. We offer

1. Replacement of old Electromechanical Relays with Numerical Relays
2. Replacement of Outdated Numerical Relays with Latest Models
3. Upgradation of existing SCADA system
4. Integration of additional Devices into existing SCADA

Our team is experienced in carrying out such services in all types of industries, from data collection, to upgradation and handing over. 

• Outage Loss Monitoring meters

Outages can cause losses in an industry. These outages are often classified as Controlled outage (normal shutdown) or uncontrolled outage (fault trip). Our meters are specifically designed to register such outages in Minutes or seconds and report to automation system. This helps in evaluation of losses on per day, per month or per year basis.

Testing and AMC Solutions

• Testing of Substation Equipment’s

Testing of substation equipment’s is a critical task with several standards defined for each equipment for testing. This ensures a proper operation in the substation in the team of experts can give you all kinds of Testing and commissioning of Substations. We can work all across the voltage levels LV, MV, HV and EHV. We have our own advanced testing equipment to carry out necessary testing of the substation and to get the work done quickly without depending on anybody.

• Maintenance for Breakers

Service life of a breaker is a parameter linked to maintenance of the breaker. Servicing reduces the issues of aging with the breaker and maintains smooth operation of the breaker during the life time.  We do breaker servicing that involves

1. Cleaning of breaker with CRC
2. Removal of old grease and re-greasing the same with recommended grease.

• Energy Meter Calibration 

The energy meter is heart of the power supply network. If the energy meter is correct the consumption recorded and the billing is correct. If the energy meter is not correct we lose on all fronts. Therefore the energy meters are required to be checked tested and calibrated on regular intervals.

Automation Solution

• Substation  Automation using RTU/PAS

Reliable transmission and distribution of electricity is the key to a Smart Grid and an integral requirement for Utilities. Substation Automation Systems (SAS) as a comprehensive part of substation control and monitoring solution provides functions such as advanced power system management and monitoring of the condition of the equipment while as service.

Reliserv is the leading enablers of substation automation solutions  including  IEC 61850 /104 /101 /103/61850 & Modbus. Reliserv substation automation offerings comply with IEC 61850 standard,, ensuring key to protection, control, automation, monitoring and real-time communications capabilities of substations with existing legacy as well as systems for future. Our smart automation reduces operational and maintenance costs, thereby increasing the performance of the plant and improving the efficiency in operations.

• Energy Monitoring Solutions and IOT Linkup for Clients

In this Energy monitoring system, SCADA is used to visualize current reading of energy meters as well as to collect the historical data for future usage. Also, SCADA is used to generate the report of necessary readings like power consumption in the hourly, daily, weekly and monthly format. We also provide IOT link for the metering scada for remote monitoring of the meter data.

• PLC Automation Solutions 

Plc automation is a process automation solution, wherein the Process is automated and customized as per client needs in a given premise. We offer different sizes and types of PLC:

1. A compact PLC is a PLC where the number of inputs and outputs are fixed.
2. A modular PLC is a system that is comprised of multiple inputs and outputs as is required by the user. Multiple modular units can be built together on a rack to suit the purpose of the user.

This reduces the time and improves process accuracy in the system.

Product Supply Solutions

We are channel partners of Siemens and traders for Schneider, GE and ABB. We supply various products from OEMS with add on services for proper installation. We Supply:

1. Numerical Relays.
2. Switchgears
3. Switchgears
4. Control and relay panels
5. Power Quality Meters
6. Auxiliary Relays
7. Automation Products
8. Siemens Motors

Rental Solutions 

Testing kits are an integral part of testing. A Good test kit ensures proper testing procedure and reliable test results. We offer omicron (Austria) make kits that are No.1 in field testing and recommended by experts. We offer:

1. Secondary Injection Kit (CMC356)
2. CT analyser(Advanced)
3. PT Analyser (Votano)
4. Tan Delta (CPC 80 + CP TD12/15)
5. Primary Injection Kit (CPC 100)
6. CB Analyzer (CIBANO 500)

Explore the comprehensive range of Automation Solutions offered by us Click Here!